Fitter Second Year – Trade Theory Set – 07By itikegyani.com / April 6, 2025 /25 20 Fitter Second Year - Trade Theory Practice Set 07यहाँ प्रत्येक पेपर में 25 महत्वपूर्ण प्रश्न होते हैं। यह क्विज ITI परीक्षा की तैयारी के लिए बेहद उपयोगी हैं, जिससे आप कहीं भी, कभी भी अध्ययन और अभ्यास कर सकते हैं। ITI के ज्ञानी द्वारा तैयार किए गए ये मॉक प्रैक्टिस पेपर परीक्षा के पैटर्न के अनुसार बनाए गए हैं, जिससे आपको वास्तविक परीक्षा का अनुभव मिलेगा और आत्मविश्वास बढ़ेगा। 1 / 25 Category: Fitter Second Year CBT Paper (TT)1. What is the name of the slip gauge grade used for inspection? | निरीक्षण के लिए प्रयुक्त स्लिप गेज ग्रेड का नाम क्या है? A. Grade I | ग्रेड "I" B. Grade '00' | ग्रेड "00" C. Grade '0' | ग्रेड "0" D. Grade II | ग्रेड "II" 2 / 25 Category: Fitter Second Year CBT Paper (TT)2. What is the name of the pipe fitting shown in the figure? | चित्र में दर्शाए गए पाइप फिटिंग आइटम का नाम क्या है? A. Concentric reducer | कंसेंट्रिक रिड्यूसर B. Coupling | युग्मन C. Reducer | रेड्यूसर D. Plug | प्लग 3 / 25 Category: Fitter Second Year CBT Paper (TT)3. What causes water dripping from the tap even after it is closed? | नल बंद होने के बाद भी नल से पानी टपकने का क्या कारण है? A. Defective washer | दोषपूर्ण वॉशर B. Loose valve | ढीला वाल्व C. Spindle thread wornout | स्पिंडल थ्रेड घिस जाना D. Bend spindle | स्पिंडल का मुड जाना 4 / 25 Category: Fitter Second Year CBT Paper (TT)4. What is the specification of sine bar? | साइन बार की विशिष्टता क्या है? A. Distance between centre points of the rollers | रोलर्स के केंद्र बिंदुओं के बीच की दूरी B. Distance between inner points of the rollers | रोलर्स के आंतरिक बिंदुओं के बीच की दूरी C. Distance between outer points of the rollers | रोलर्स के बाहरी बिंदुओं के बीच की दूरी D. Distance between the edges of the sine bar | साइन बार के किनारों के बीच की दूरी 5 / 25 Category: Fitter Second Year CBT Paper (TT)5. Which valve controls the direction of the flow of fluid? | कौन सा वाल्व द्रव के प्रवाह की दिशा को कंट्रोल करता है? A. Pressure control valve | दबाव नियंत्रण वाल्व B. Non-return valve | गैर वापसी वाल्व C. Flow control valve | प्रवाह नियंत्रण वाल्व D. Directional control valve | दिशात्मक नियंत्रण वाल्व 6 / 25 Category: Fitter Second Year CBT Paper (TT)6. What is the name of the crane shown in the figure? | चित्र में दिखाए गए क्रेन का नाम क्या है? A. Bracket jib crane | ब्रोचिट जिब क्रेन B. Pillar jib crane | पिलर जिब क्रेन C. Travelling crane | ट्रैवेलिंग क्रेन D. Gantry crane | गैन्ट्री क्रेन 7 / 25 Category: Fitter Second Year CBT Paper (TT)7. What is the name of the part marked as 'X' shown in the figure? | चित्र में दिखाए गए 'X' से चिह्नित भाग का नाम क्या है? A. Pitch gauge | पिच गेज B. Depth gauge | गहराई गेज C. Template | टेम्पलेट D. Profile plate | प्रोफ़ाइल प्लेट 8 / 25 Category: Fitter Second Year CBT Paper (TT)8. What is the name of the pneumatic valve symbol shown in the figure? | चित्र में दर्शाए गए वायवीय वाल्व प्रतीक का क्या नाम है? A. Flow control valve | प्रवाह नियंत्रण वाल्व B. Pressure valve | प्रेशर वाल्व C. Roller valve | रोलर वाल्व D. Directional control valve | दिशात्मक नियंत्रण वाल्व 9 / 25 Category: Fitter Second Year CBT Paper (TT)9. What is the name of the bearing shown in the figure? | चित्र में दिखाए गए बियरिंग का नाम क्या है? A. Ball bearing | बॉल बियरिंग B. Journal bearing | जर्नल बीयरिंग C. Thrust bearing | थ्रस्ट बियरिंग D. Roller bearing | रोलर बीयरिंग 10 / 25 Category: Fitter Second Year CBT Paper (TT)10. Which aligns the machine tools accurately? | कौन मशीन टूल्स को सटीक रूप से संरेखित करता है? A. Try square | ट्राई स्केवयर B. L' Square L' स्कवेयर C. Precision spirit level | परिशुद्धता स्पिरिट का स्तर D. Steel rule स्टील रूल 11 / 25 Category: Fitter Second Year CBT Paper (TT)11. What is the use of tab washers? | टैब वॉशर का उपयोग क्या है? A. Locking the nut from the top | ऊपर से नट को लॉक करना B. Locking the nut at the center | केंद्र पर नट को लॉक करना C. Locking the nut from the bottom | नीचे से नट को लॉक करना D. Locking the nut at the corner | कोने पर नट को लॉक करना 12 / 25 Category: Fitter Second Year CBT Paper (TT)12. Why copper is extensively used in electrical cables and appliances? | विद्युत केबलों और उपकरणों में तांबे को बड़े पैमाने पर उपयोग क्यों किया जाता है? A. Ductile metal | तन्य धातु B. Good conductor | गुड कंडक्टर C. Easy soldering | आसान सोल्डरिंग D. Cheap in cost | लागत में सस्ता 13 / 25 Category: Fitter Second Year CBT Paper (TT)13. In which type of belt drive, the driven shaft will rotate in the opposite direction to the driver shaft? | किस प्रकार की बेल्ट ड्राइव में, चालित शाफ्ट चालक शाफ्ट के विपरीत दिशा में घूमेगा? A. Stepped drive | स्टेपड ड्राइव B. Right angled belt drive | राइट एंगल्ड बेल्ट ड्राइव C. Cross belt drive | क्रॉस बेल्ट ड्राइव D. Open belt drive | ओपन बेल्ट ड्राइव 14 / 25 Category: Fitter Second Year CBT Paper (TT)14. What is the name of the fixture shown in the figure? | चित्र में दिखाए गए उपकरण का नाम क्या है? A. Angel plate fixture | एंगल प्लेट फिक्स्चर B. Plate fixture | प्लेट फिक्स्चर C. Indexing plate fixture | इंडेक्सिंग प्लेट फिक्स्चर D. Modified angle plate fixture | मॉडिफाइड एंगल प्लेट फिक्स्चर 15 / 25 Category: Fitter Second Year CBT Paper (TT)15. What is the name of the part marked as 'X' shown in the figure? | चित्र में दिखाए गए 'X' के रूप में चिह्नित भाग का नाम क्या है? A. Inner race | इनर रेस B. Ball cage | बॉल केज C. Ball | बॉल सेपरेटर D. Outer race | आउटर रेस 16 / 25 Category: Fitter Second Year CBT Paper (TT)16. Which device used to remove dust, chips and other foreign particles from the fluid? | द्रव से धूल, चिप्स और अन्य विदेशी कणों को हटाने के लिए किस उपकरण का उपयोग किया जाता है? A. Filter | फ़िल्टर B. Regulator | रेगुलेटर C. Pressure regulating valve | प्रेशर रेगुलेटिंग वाल्व D. Accumulator | अक्यूम्यलेटर 17 / 25 Category: Fitter Second Year CBT Paper (TT)17. Which process is carried out with abrasive sticks to correct the profile of internal cylindrical surfaces? | आंतरिक बेलनाकार सतहों की प्रोफाइल को सही करने के लिए अपघर्षक छड़ियों के साथ कौन सी प्रक्रिया की जाती है? A. Grinding | ग्राइंडिंग B. Filing | फाइलिंग C. Honing | होनिंग D. Lapping | लैपिंग 18 / 25 Category: Fitter Second Year CBT Paper (TT)18. Which material is used to make slip gauge block? | स्लिप गेज ब्लॉक बनाने के लिए किस मटेरियल का उपयोग किया जाता है? A. Tool steel | टूल स्टील B. Low grade steel | लो ग्रेड स्टील C. High carbon steel | उच्च कार्बन स्टील D. High grade steel | हाई ग्रेड स्टील 19 / 25 Category: Fitter Second Year CBT Paper (TT)19. Which metal is extracted from Bauxite ore? | बॉक्साइट अयस्क से कौन सी धातु निकाली जाती है? A. Aluminium | एल्युमिनियम B. Zinc | जस्ता C. Copper | तांबा D. Brass | पीतल 20 / 25 Category: Fitter Second Year CBT Paper (TT)20. What is the name of the valve shown in the figure? | चित्र में दिखाए गए वाल्व का नाम क्या है? A. 5 port 2 position valve | 5 पोर्ट 2 पोजीशन वाल्व B. 4 port 3 position valve | 4 पोर्ट 3 पोजीशन वाल्व C. 4 port 2 position valve | 4 पोर्ट 2 पोजीशन वाल्व D. 3 port 2 position valve | 3 पोर्ट 2 पोजीशन वाल्व 21 / 25 Category: Fitter Second Year CBT Paper (TT)21. What is the name of the operation that corrects the profiles of cylindrical surfaces and removes taper? | उस ऑपरेशन का नाम क्या है जो बेलनाकार सतहों की प्रोफाइल को सही करता है और टेपर को हटाता है? A. Grinding | ग्राइंडिंग B. Boring | बोरिंग C. Honing | होनिंग D. Reaming | रीमिंग 22 / 25 Category: Fitter Second Year CBT Paper (TT)22. What is the value of bar in metric unit of pressure? | प्रेशर की मीट्रिक इकाई में बार का मान क्या है? A. 1 Kg/cm² B. 1 Kg/mm² C. 1 Kg/dm² D. 1 Kg/m² 23 / 25 Category: Fitter Second Year CBT Paper (TT)23. Which file is used for finishing sharp corners? | नुकीले कोनों को फिनिश करने के लिए किस फाइल का उपयोग किया जाता है? A. Warding file | वार्डिंग फ़ाइल B. Pillar file | पिलर फाइल C. Barrette file | बैरेट फ़ाइल D. Riffler file | रिफ्लेर फाइल 24 / 25 Category: Fitter Second Year CBT Paper (TT)24. Which cutting oil is used in automatic lathes? | ऑटोमैटिक लैट्स में कौन सा कटिंग ऑयल इस्तेमाल किया जाता है? A. Fatty oil | वसायुक्त तेल B. Compounded (or) blended oil | मिश्रित (या) ब्लेंडेड तेल C. Straight mineral oil | सीधा खनिज तेल D. Soluble oil | सोल्युबल तेल 25 / 25 Category: Fitter Second Year CBT Paper (TT)25. What is the name of the file shown in the figure? | चित्र में दर्शाई गई फ़ाइल का नाम क्या है? A. Warding file | वार्डिंग फ़ाइल B. Pillar file | पिलर फाइल C. Swiss pattern file | स्विस पैटर्न फ़ाइल D. Dread naught file | ड्रेड नॉट फ़ाइल Your score isThe average score is 56% 0% Restart quiz Exit Workshop CalculationEngineering DrawingEmployability SkillFitter Second Year CBT PapersWhatsApp और YouTube चैनल से जुड़े रहनाWhats App अत्यधिक चर्चा में SCVT पोर्टल करेक्शन गाइड: सत्र 2025 में नाम, जन्म तिथि और अन्य विवरण सुधार की पूरी जानकारी SBI Specialist Cadre Officer (Manager/Deputy Manager Digital Platforms) Recruitment 2025- Only Interview SBI Specialist Cadre Officer (Credit Analyst) Recruitment 2025- Only Interview 🚀 भारत की ईवी क्रांति का हिस्सा बनें | साइट इंजीनियर (इलेक्ट्रिकल) की भर्ती ⚡ आईटीआई रिजल्ट 2025: SIDH पोर्टल पर ग्रिवांस कर सुधारें अपनी गलती (अंतिम तिथि 19 सितम्बर) Uttar Pradesh 🚨 आईटीआई में रिक्त सीटों के लिए नया विकल्प पंजीकरण शुरू – अगस्त 2025 सत्र के लिए सुनहरा मौका – Apply Online