Draughtsman Mechanical First Year CBT Paper – Free Practice Set -3

14

यह पेपर 2 घंटे का है 2 घंटे बाद पेपर अपने आप सबमिट हो जायेगा और आप चाहें तो 2 घंटे से पहले भी सबमिट कर सकते है|

सॉरी समय समाप्त हो गया|


Draughtsman Mechanical CBT Paper First Year (Quiz -3)

इस पेपर में 75 प्रशन है जिसमे Trade Tehory  के 44 प्रशन, Workshop Calculation and Science के 06 प्रशन, Employability Skill  के 25 प्रशन , प्रत्येक प्रशन 2 मार्क्स का है और किसी प्रकार की नेगेटिव मार्किंग नहीं है|

1 / 75

Category: Workshop Calculation and Science CBT Paper (I)

1. What are the two classifications of system of units?/
इकाइयों की प्रणाली के दो प्रकार कोनसे हैं?

2 / 75

Category: Workshop Calculation and Science CBT Paper (I)

2. How many millimetres are there in 1 inch? |
1 इंच में कितने मिलीमीटर होते हैं?

3 / 75

Category: Workshop Calculation and Science CBT Paper (I)

3. Which among the following is an insulator? |
निम्नलिखित में से कौन एक कुचालक है?

4 / 75

Category: Workshop Calculation and Science CBT Paper (I)

4. What is called mass per unit volume of a substances?|
किसी पदार्थ के द्रव्यमान प्रति इकाई आयतन को क्या कहते हैं?

5 / 75

Category: Workshop Calculation and Science CBT Paper (I)

5. Convert 0.456 decimal fraction into percentage? |
0.456 दशमलव भिन्न को प्रतिशत में बदलिये?

6 / 75

Category: Workshop Calculation and Science CBT Paper (I)

6. What is the name of furnace to obtain cast iron? |

कच्चा लोहा प्राप्त करने के लिए भट्ठी का क्या नाम है?

7 / 75

Category: Draughtsman Mechanical First Year CBT Paper (TT)

1. What does UCS in the context of CAD mean? |
CAD के संदर्भ में UCS का क्या अर्थ है?

8 / 75

Category: Draughtsman Mechanical First Year CBT Paper (TT)

2. What is angle of isometric view? |
सममितीय दृश्य का कोण क्या है?

9 / 75

Category: Draughtsman Mechanical First Year CBT Paper (TT)

3. What is name of object as shown in figure? |
चित्र में दिखाए अनुसार ऑब्जेक्ट का नाम क्या है?

10 / 75

Category: Draughtsman Mechanical First Year CBT Paper (TT)

4. What is the main constituent of moulding sand? |
मौल्डिंग सैंड का मुख्य घटक क्या है?

11 / 75

Category: Draughtsman Mechanical First Year CBT Paper (TT)

5. Which is reflex angle? |
रिफ्लेक्स कोण कौन सा है?

12 / 75

Category: Draughtsman Mechanical First Year CBT Paper (TT)

6. Which type of operation done by lathe for preparing diamond cut patterns on surface? |
डायमंड कट पैटर्न तैयार करने के लिए खराद द्वारा किस प्रकार का संचालन किया जाता है?

13 / 75

Category: Draughtsman Mechanical First Year CBT Paper (TT)

7. What is the outer most part of screw thread? |
स्क्रू थ्रेड का सबसे बाहरी हिस्सा क्या है?

14 / 75

Category: Draughtsman Mechanical First Year CBT Paper (TT)

8. What is the unit of energy? |
ऊर्जा की इकाई क्या है?

15 / 75

Category: Draughtsman Mechanical First Year CBT Paper (TT)

9. Which is the smallest diameter of a screw thread? |
एक स्क्रू थ्रेड का सबसे छोटा व्यास कौन सा है?

16 / 75

Category: Draughtsman Mechanical First Year CBT Paper (TT)

10. What is the representation of material shown in figure? |
नीचे दी गई आकृति में दिखाई गई सामग्री का प्रतिनिधित्व क्या है?

17 / 75

Category: Draughtsman Mechanical First Year CBT Paper (TT)

11. Which one of these fastener is used to prevent rotation between two parts? |
इन फास्टनर में से किसका उपयोग दो भागों के बीच रोटेशन को रोकने के लिए किया जाता है?

18 / 75

Category: Draughtsman Mechanical First Year CBT Paper (TT)

12. When a vertical cylinder is penetrated by a horizontal cylinder, the top view of the intersection is___________ |
जब एक ऊर्ध्वाधर सिलेंडर एक क्षैतिज सिलेंडर द्वारा प्रवेश किया जाता है, तो चौराहे का शीर्ष दृश्य होता है?

19 / 75

Category: Draughtsman Mechanical First Year CBT Paper (TT)

13. What is the name of the curve of intersection of a vertical cylinder with an auxiliary vertical plane? |
एक सहायक ऊर्ध्वाधर तल के साथ एक ऊर्ध्वाधर सिलेंडर के प्रतिच्छेदन वक्र का नाम क्या है?

20 / 75

Category: Draughtsman Mechanical First Year CBT Paper (TT)

14. What is the name that distance from a point on one thread to the corresponding point on the next thread? |
एक थ्रेड पर एक बिंदु से अगले थ्रेड पर संबंधित बिंदु तक की दूरी को क्या कहते हैं?

21 / 75

Category: Draughtsman Mechanical First Year CBT Paper (TT)

15. Chord scale is used for? |
कॉर्ड स्केल का प्रयोग किसके लिए किया जाता है?

22 / 75

Category: Draughtsman Mechanical First Year CBT Paper (TT)

16. What is the angle of "return bend" fitting? |
"रिटर्न बेंड" फिटिंग का कोण क्या है?

23 / 75

Category: Draughtsman Mechanical First Year CBT Paper (TT)

17. What is the angle set between two axis of drafter? |
ड्राफ्टर के दो अक्षों के बीच एक सेट क्या है?

24 / 75

Category: Draughtsman Mechanical First Year CBT Paper (TT)

18. Which of these operations cannot be done on the lathe? |
इनमें से कौन-सा ऑपरेशन लेथ पर नहीं किया जा सकता है?

25 / 75

Category: Draughtsman Mechanical First Year CBT Paper (TT)

19. What is representative fraction of a scale? |
स्केल का प्रतिनिधि अंश क्या है?

26 / 75

Category: Draughtsman Mechanical First Year CBT Paper (TT)

20. What is the ratio of length and width of an arrow head? |
एक तीर के शीर्ष की लंबाई और चौड़ाई का अनुपात क्या है?

27 / 75

Category: Draughtsman Mechanical First Year CBT Paper (TT)

21. Where the study of intersection of surfaces help? |
सतहों के प्रतिच्छेदन का अध्ययन कहाँ मदद करता है?

28 / 75

Category: Draughtsman Mechanical First Year CBT Paper (TT)

22. What do you call when train of more gears are combined? |
जब अधिक गियर्स की ट्रेन कंबाइन हो जाती है तो आप क्या कहते हैं?

29 / 75

Category: Draughtsman Mechanical First Year CBT Paper (TT)

23. In which method non isometric lines are suited for isometric view of an object consisting of number of planes at different angles? |अलग-अलग कोणों पर प्लान की संख्या से युक्त किसी वस्तु के आइसोमेट्रिक दृश्य के लिए गैर आइसोमेट्रिक लाइनें किस विधि से अनुकूल हैं?

30 / 75

Category: Draughtsman Mechanical First Year CBT Paper (TT)

24. Which type of section is to show the shape rotated towards plane of projection of objects such as spokes and ribs? |
जहां एक घुमाए गए खंड के रूप में भी जाना जाता है, एक दृश्य जैसे कि प्रवक्ता और पसलियों के आकार को दिखाने के लिए इस्तेमाल किया जाता है?

31 / 75

Category: Draughtsman Mechanical First Year CBT Paper (TT)

25. Which method of free hand sketching is shown in figure? |
फ्री हैंड स्केचिंग की कौन सी विधि चित्र में दिखाई गई है।

32 / 75

Category: Draughtsman Mechanical First Year CBT Paper (TT)

26. What type of section, one quarter of the object is removed? |
किस प्रकार का अनुभाग, वस्तु का एक चौथाई हिस्सा हटा दिया जाता है

33 / 75

Category: Draughtsman Mechanical First Year CBT Paper (TT)

27. Which of the following is a flexible coupling? |
निम्नलिखित में से कौन सा एक फ्लेक्सिबल कपलिंग है

34 / 75

Category: Draughtsman Mechanical First Year CBT Paper (TT)

28. A thin coating of ____ is applied to steel or iron pipes to make galvanized pipes. |
गैल्वनाइज्ड पाइप बनाने के लिए स्टील या लोहे के पाइप पर ____ की एक पतली परत लगाई जाती है।

35 / 75

Category: Draughtsman Mechanical First Year CBT Paper (TT)

29. Which of the following is not a part of a rivet? |
निम्नलिखित में से कौन एक रिवेट का हिस्सा नहीं है?

36 / 75

Category: Draughtsman Mechanical First Year CBT Paper (TT)

30. Which system of dimensioning technique is shown in figure? |
आयाम तकनीक की किस प्रणाली को अंजीर में दिखाया गया है।

37 / 75

Category: Draughtsman Mechanical First Year CBT Paper (TT)

31. Which is an acute angle? |
एक न्यून कोण कौन सा है?

38 / 75

Category: Draughtsman Mechanical First Year CBT Paper (TT)

32. What is the term for a straight line joining ends of an arc on a circle? |
एक सर्कल पर एक चाप के सिरों को जोड़ने वाली सीधी रेखा के लिए शब्द क्या है?

39 / 75

Category: Draughtsman Mechanical First Year CBT Paper (TT)

33. Which type of motions are the cotter joints used? |
कोटर जॉइंट का उपयोग किस प्रकार की गतियों के लिए किया जाता है?

40 / 75

Category: Draughtsman Mechanical First Year CBT Paper (TT)

34. What is name of object as shown in figure? |
आकृति में दिखाए अनुसार वस्तु का नाम क्या है?

41 / 75

Category: Draughtsman Mechanical First Year CBT Paper (TT)

35. "When rivet is specified as a 20 mm rivet " what does it mean? |
"जब रिवेट को 20 मिमी रिवेट" के रूप में निर्दिष्ट किया जाता है तो इसका क्या मतलब है?

42 / 75

Category: Draughtsman Mechanical First Year CBT Paper (TT)

36. What is the best example of shrinkage fit? |
श्रिंकेज फिट का सबसे अच्छा उदाहरण क्या है?

43 / 75

Category: Draughtsman Mechanical First Year CBT Paper (TT)

37. How the size of the letter is specified? |
पत्र का आकार कैसे निर्दिष्ट किया जाता है?

44 / 75

Category: Draughtsman Mechanical First Year CBT Paper (TT)

38. What is the grade of the hardest pencil? |
सबसे कठिन पेंसिल का ग्रेड क्या है?

45 / 75

Category: Draughtsman Mechanical First Year CBT Paper (TT)

39. What is the conventional representation in given below figure? |
नीचे दिए गए आंकड़े में पारंपरिक प्रतिनिधित्व क्या है?

46 / 75

Category: Draughtsman Mechanical First Year CBT Paper (TT)

40. How circle will appear on an isometric drawing? |
एक इसोमेट्रिक ड्राइंग पर वृत्त कैसा दिखाई देगा?

47 / 75

Category: Draughtsman Mechanical First Year CBT Paper (TT)

41. What is CD-ROM? |
CD-ROM क्या है?

48 / 75

Category: Draughtsman Mechanical First Year CBT Paper (TT)

42. Identify which system of dimensioning in the figure given? |
दिए गए चित्र में पहचानें आयाम की कौन सी प्रणाली है ?

49 / 75

Category: Draughtsman Mechanical First Year CBT Paper (TT)

43. What is the deference between maximum and minimum limit of sizes? |
अधिकतम और न्यूनतम आकार के बीच अंतर क्या है?

50 / 75

Category: Draughtsman Mechanical First Year CBT Paper (TT)

44. Where is cycloided profile gear are used? |
साइक्लॉइड प्रोफ़ाइल गियर का उपयोग कहां किया जाता है?

51 / 75

Category: Employability Skill CBT Paper (I)

1. In Excel, the intersection of a row and column is called a _________|
एक्सेल में, किसी रो (पंक्ति) और कॉलम (स्तंभ) के इंटरसेक्शन (प्रतिच्छेदन) को ............ कहा जाता है l

52 / 75

Category: Employability Skill CBT Paper (I)

2. You have greeted the customer. Choose which of the following statements you should use to complete the greeting.|
आपने ग्राहक को बधाई दी है। ग्रीटिंग को पूरा करने के लिए आपको निम्नलिखित में से किस कथन का उपयोग करना चाहिए चुनें।

53 / 75

Category: Employability Skill CBT Paper (I)

3. When you send your resume through email, you are sending it in the form of ______.|
जब आप अपना बायोडाटा ईमेल के माध्यम से भेजते हैं, तो आप उसे ______ के रूप में भेज रहे होते हैं।

54 / 75

Category: Employability Skill CBT Paper (I)

4. Time management………|
समय प्रबंधन………।

55 / 75

Category: Employability Skill CBT Paper (I)

5. Which one of the following is a good office etiquette? |
निम्नलिखित में से कौन सा एक अच्छा कार्यालय शिष्टाचार है?

56 / 75

Category: Employability Skill CBT Paper (I)

6. Which of these is not an online job search platform? |
इनमें से कौन एक ऑनलाइन जॉब सर्च प्लेटफॉर्म नहीं है?

57 / 75

Category: Employability Skill CBT Paper (I)

7. _____ is the brain of the computer. |
_____कंप्यूटर का मस्तिष्क है।

58 / 75

Category: Employability Skill CBT Paper (I)

8. Dedication to a particular work is called_________ |
किसी विशेष कार्य के लिए समर्पण को _________ कहा जाता है

59 / 75

Category: Employability Skill CBT Paper (I)

9. The expansion of SIDO is………… |
SIDO का विस्तार ………

60 / 75

Category: Employability Skill CBT Paper (I)

10. Ethics means …. |
नैतिकता का अर्थ है....।

61 / 75

Category: Employability Skill CBT Paper (I)

11. Which one is NOT a conjunction? |
कौन सा एक संयोजन नहीं है?

62 / 75

Category: Employability Skill CBT Paper (I)

12. Debit card will have how many digit numbers ______|
डेबिट कार्ड में कितने अंकों की संख्या होगी…….।

63 / 75

Category: Employability Skill CBT Paper (I)

13. Which one is NOT an essential characteristic to achieve success? |
सफलता प्राप्त करने के लिए कौन सा आवश्यक लक्षण नहीं है?

64 / 75

Category: Employability Skill CBT Paper (I)

14. Which one is an output device of the computer? |
कंप्यूटर का आउटपुट डिवाइस कौन सा है?

65 / 75

Category: Employability Skill CBT Paper (I)

15. Which of the following statements is true?|
निम्नलिखित में से कौन से वतव्य विवरण सत्य हैं?

66 / 75

Category: Employability Skill CBT Paper (I)

16. Fill in the blank with proper reflexive pronoun. “She has hurt___________”|
रिक्त स्थान में उचित प्रतिवर्ती सर्वनाम के साथ भरें। “She has hurt___________”

67 / 75

Category: Employability Skill CBT Paper (I)

17. In an email, where will you add the recipient email address whom you want to send the copy of an email? |
एक ईमेल में, आप प्राप्तकर्ता का ई-मेल एड्रेस (ईमेल का पता) कहां जोड़ेंगे, जिसे आप ईमेल की कॉपी भेजना चाहते हैं?

68 / 75

Category: Employability Skill CBT Paper (I)

18. Something is made of different types of units…….|
कुछ न कुछ विभिन्न प्रकार की इकाइयों से बनता है…….।

69 / 75

Category: Employability Skill CBT Paper (I)

19. What does ‘ASAP’ stand for, in SMS language?|
एसएमएस भाषा में "ASAP" का क्या अर्थ है ?

70 / 75

Category: Employability Skill CBT Paper (I)

20. The ability to do is ______ |
...... करने की क्षमता है।

71 / 75

Category: Employability Skill CBT Paper (I)

21. NAPS Stands for _______|
NAPS का मतलब ________

72 / 75

Category: Employability Skill CBT Paper (I)

22. What is the cell address of 4th row and 4th column?|
चौथी रो (पंक्ति) और चौथे कॉलम (स्तंभ) का सेल एड्रेस क्या होता है?

73 / 75

Category: Employability Skill CBT Paper (I)

23. What makes General AI different from other types of AI? |
जनरल ए.आई. अन्य प्रकार की ए.आई. से अलग क्या बनाता है?

74 / 75

Category: Employability Skill CBT Paper (I)

24. Choose the odd word. |
odd (विषम) शब्द चुनें।

75 / 75

Category: Employability Skill CBT Paper (I)

25. Pronunciation refers to___________.|
उच्चारण ___________ को संदर्भित करता है

Your score is

The average score is 40%

0%

Exit

WhatsApp और YouTube चैनल से जुड़े रहना

Leave a Comment

Your email address will not be published. Required fields are marked *

You cannot copy content of this page

Scroll to Top