Electrician Second Year CBT Paper –Free Practice Set -4By itikegyani.com / November 22, 2024 /75 यह पेपर 2 घंटे का है 2 घंटे बाद पेपर अपने आप सबमिट हो जायेगा और आप चाहें तो 2 घंटे से पहले भी सबमिट कर सकते है| पेपर देने के लिए आपको हमारी वेबसाइट पर login करना अनिवार्य है|सॉरी समय समाप्त हो गया| Electrician CBT Paper Second Year (Quiz -4)इस पेपर में 75 प्रशन है जिसमे Trade Tehory के 38 प्रशन, Workshop Calculation and Science के 06 प्रशन, Engineering Drawing के 06 प्रशन, Employability Skill के 25 प्रशन , प्रत्येक प्रशन 2 मार्क्स का है और किसी प्रकार की नेगेटिव मार्किंग नहीं है| 1 / 75 Category: ES 2 Year Module 1- Basic Carrer Skills1. What is workplace etiquette? A. None of these B. Everyday manners outside of work C. Casual behavior with colleagues D. Proper behavior in the workplace based on respect and professionalism 2 / 75 Category: Workshop Calculation and Science CBT Paper (II)1. Which is the formula forकौन सा सूत्र है A. (aᵐ)ⁿ B. aᵐ⁺ⁿ C. aᵐ*ⁿ D. aᵐ⁻ⁿ 3 / 75 Category: Workshop Calculation and Science CBT Paper (II)2. What is the expanded form of (a+b)2?|(a+b)2 का विस्तारित रूप क्या है? A. a² + 2ab + b² B. a² - 2ab + b² C. -a² - 2ab + b² D. a² + 2ab - b² 4 / 75 Category: Workshop Calculation and Science CBT Paper (II)3. What is the value of 14x+3y+25x+2y? |14x +3y+25x+2y का मान क्या है? A. 39x + 5y B. 17x + 27y C. 16x + 28y D. 44xy 5 / 75 Category: Workshop Calculation and Science CBT Paper (II)4. How the years is denoted in simple interest calculations? |साधारण ब्याज में साल को कैसे दर्शाया जाता है? A. r B. P C. n D. I 6 / 75 Category: Workshop Calculation and Science CBT Paper (II)5. What is denoted as 'I'? |आई (I) किसको निरूपित करता है? A. Interest | इंटरेस्ट B. Year | ईयर C. Rate | रेट D. Principal | प्रिंसिपल 7 / 75 Category: Workshop Calculation and Science CBT Paper (II)6. Which type of stress? |कौन-सा प्रतिबल है? A. Torsional stress | टॉर्सनल प्रतिबल B. Shear stress | कर्तन प्रतिबल C. Compressive stress | सम्पीडन प्रतिबल D. Tensile stress | तनाव प्रतिबल 8 / 75 Category: Engineering Drawing CBT Paper (II)1. Voltage less than 250 volt is called______. |250 वोल्ट से कम वोल्टता ____ कहलाती है A. LT (Low Tension) | LT (लो टेंशन) B. MT (Medium Tension) | MT(मध्यम टेंशन) C. EHT (Extra High Tension) | EHT (अतिरिक्त उच्च टेंशन) D. HT (High Tension) | HT (उच्च टेंशन) 9 / 75 Category: Engineering Drawing CBT Paper (II)2. Which is protective device? |सुरक्षात्मक उपकरण कौन सा है? A. Fuse | फ्यूज़ B. Capacitor | कैपसिटर C. Resistor | रेसिस्टार D. Magnet | मैग्नेट 10 / 75 Category: Engineering Drawing CBT Paper (II)3. What is the name of the gateगेट का नाम क्या है? A. OR Gate | OR गेट B. NOT Gate | NOT गेट C. AND Gate | AND गेट D. Ex-NOR Gate | Ex-Nor गेट 11 / 75 Category: Engineering Drawing CBT Paper (II)4. Identify the wave form. |वेव फार्म को पहचानें A. Sine wave | साइन वेव B. Square wave | स्क्वेर वेव C. Triangle wave | त्रिकोण वेव D. Saw-tooth wave | सॉ-टूथ वेव 12 / 75 Category: Engineering Drawing CBT Paper (II)5. Is this a symbol of DC motor?क्या ये DC मोटर का प्रतीक है? A. Yes | हाँ B. No | नहीं 13 / 75 Category: Engineering Drawing CBT Paper (II)6. Is this photo diode?क्या ये फोटो डायोड का है? A. No | नहीं B. Yes | हाँ 14 / 75 Category: ES 2 Year Module 3- Internet Skills1. While thinking about learning, what are the questions you can ask yourself? A. All of these B. What did I learn? C. How can I learn better? D. Was it easy or difficult to learn? 15 / 75 Category: Electrician Second Year CBT Paper (TT)1. Which type of D.C generator is used for arc welding? |आर्क वेल्डिंग के लिए किस प्रकार के D.C जनरेटर का उपयोग किया जाता है? A. Differential compound generator | विभेदक यौगिक जनरेटर B. Cumulative compound generator | संचयी यौगिक जनरेटर C. Series generator | श्रेणी जनरेटर D. Shunt generator | शंट जनरेटर 16 / 75 Category: Electrician Second Year CBT Paper (TT)2. What is the name of the part marked as ‘X’ of the winding machine as shown in the figure? |चित्र में दर्शाए अनुसार वाइंडिंग मशीन के ‘X’ से चिह्नित भाग का नाम क्या है? A. Wire guides | तार गाइड B. Spool carrier | स्पूल वाहक C. Wire feed | तार का चारा D. Mandrel | खराद का धुरा 17 / 75 Category: Electrician Second Year CBT Paper (TT)3. Which type of single phase motor is illustrated as shown in the diagram? |चित्र में दिखाए अनुसार किस प्रकार की एकल चरण मोटर को दर्शाया गया है? A. Permanent capacitor motor | स्थायी संधारित्र मोटर B. Capacitor start capacitor run motor | कैपेसिटर स्टार्ट कैपेसिटर रन मोटर C. Capacitor start induction run motor | कैपेसिटर स्टार्ट इंडक्शन रन मोटर D. Universal motor | यूनिवर्सल मोटर 18 / 75 Category: Electrician Second Year CBT Paper (TT)4. What is the name of the test as shown in the circuit? |सर्किट में दिखाए गए परीक्षण का नाम क्या है? A. Open circuit test | ओपन सर्किट टेस्ट B. Polarity test | ध्रुवता जांच C. No load test | कोई लोड टेस्ट नहीं D. Blocked rotor test | ब्लॉक्ड रोटर टेस्ट 19 / 75 Category: Electrician Second Year CBT Paper (TT)5. What is the formula to calculate the back emf of a D.C motor? |D.C मोटर के बैक emf की गणना करने का सूत्र क्या है? A. Eb = V – Iₐ Rₐ Volts B. Eb = (V/ IₐRₐ) Volts C. Eb = V + Iₐ Rₐ Volts D. Eb = V x Iₐ Rₐ Volts 20 / 75 Category: Electrician Second Year CBT Paper (TT)6. Which is the correct sequence of operation of contactors for operating an automatic star delta starter? |स्वचालित स्टार डेल्टा स्टार्टर के संचालन के लिए संपर्ककों के संचालन का सही क्रम कौन सा है? A. Main→Star→Delta→Timer B. Star→Timer→Delta→Main C. Star→Main→Timer→Delta D. Main→Timer→Delta→Star 21 / 75 Category: Electrician Second Year CBT Paper (TT)7. What is the function of collar as shown in the figure? |जैसा कि चित्र में दिखाया गया है, कॉलर का क्या कार्य है? A. Provides insulation around field | क्षेत्र के चारों ओर इन्सुलेशन प्रदान करता है B. Provides insulation for coil tapping | कुंडल टेपिंग के लिए इन्सुलेशन प्रदान करता है C. Helps tightening material for flange | निकले हुए किनारे के लिए सामग्री को कसने में मदद करता है D. Provides insulation for heat transfer from coil | कुंडल से ऊष्मा स्थास्तांतरण के लिए इन्सुलेशन प्रदान करता है 22 / 75 Category: Electrician Second Year CBT Paper (TT)8. Which type of machine in industries is provided with multi motor electric drive? |उद्योगों में किस प्रकार की मशीन मल्टी मोटर इलेक्ट्रिक ड्राइव के साथ प्रदान की जाती है? A. Shearing machine | शेयरिंग मशीन B. Rolling machine | घुमाने वाली मशीन C. Air Compressor | एयर कम्पेसर D. Heavy duty electric drilling machine | भारी कार्य इलेक्ट्रिक ड्रिलिंग मशीन 23 / 75 Category: Electrician Second Year CBT Paper (TT)9. What is the voltage regulation in percentage if the load is removed from an alternator, the voltage rises from 480V to 660V. |यदि किसी अल्टरनेटर से लोड हटा दिया जाए तो वोल्टेज 480V से 660V तक बढ़ जाता है तो वोल्टेज विनियमन प्रतिशत में क्या होगा? A. 27.2% B. 37.5% C. 32.5% D. 38.5% 24 / 75 Category: Electrician Second Year CBT Paper (TT)10. How the voltage is received in the rotor of induction motor? |इंडक्शन मोटर के रोटर में वोल्टेज कैसे प्राप्त होता है? A. Direct connection from stator | स्टेटर से सीधा संबंध B. By the transformer action of stator and rotor | स्टेटर और रोटर का ट्रांसफार्मर कार्य द्वारा C. Direct connection to rotor from supply | आपूर्ति से रोटर का सीधा संबंध D. Due to back emf produced in stator | स्टेटर में उत्पादित बैक ईएमएफ के कारण 25 / 75 Category: Electrician Second Year CBT Paper (TT)11. What is the full form of NTC resistors? |NTC रेसिस्टर्स का पूर्ण रूप क्या है? A. Negative Temperature Co-efficient Resistor | ऋणात्मक तापमान गुणांक प्रतिरोधक B. Natural Temperature Co-efficient Resistor | प्राकृतिक तापमान गुणांक प्रतिरोधक C. Neutral Temperature Co-efficient Resistor | तटस्थ तापमान गुणांक प्रतिरोधक D. Non Temperature Co-efficient Resistor | गैर तापमान गुणांक प्रतिरोधक 26 / 75 Category: Electrician Second Year CBT Paper (TT)12. What is the function of the part marked as ‘X’ of the rotary converter as shown in the figure? |जैसा कि चित्र में दिखाया गया है, रोटरी कनवर्टर के 'X' के रूप में चिह्नित भाग का क्या कार्य है? A. Collects the direct current | प्रत्यक्ष धारा एकत्रित करता है B. Converts AC into DC | AC को DC में परिवर्तित करता है C. Reduces voltage drop | वोल्टेज ड्रॉप को कम करता है D. Collects the alternating current | प्रत्यावर्ती धारा एकत्रित करता है 27 / 75 Category: Electrician Second Year CBT Paper (TT)13. Which type of armature winding is illustrated as shown in the figure? |चित्र में दिखाए अनुसार किस प्रकार की आर्मेचर वाइंडिंग दर्शाई गई है? A. Retrogressive lap winding | रिट्रोग्रेसिव लैप वाइंडिंग B. Triplex wave winding | ट्रिपलेक्स वेव वाइंडिंग C. Duplex wave winding | ड्यूपलेक्स वेव वाइंडिंग D. Progressive lap winding | प्रगतिशील लैप वाइंडिंग 28 / 75 Category: Electrician Second Year CBT Paper (TT)14. Which circuit breaker is installed along with wiring circuit against leakage current protection? |लीकेज करंट प्रोटेक्शन से बचाव हेतु वायरिंग सर्किट के साथ कौन सा सर्किट ब्रेकर लगाया जाता है? A. MCB | एमसीबी B. OCB | ओसीबी C. ELCB | इएलसीबी D. MCCB | एमसीसीबी 29 / 75 Category: Electrician Second Year CBT Paper (TT)15. What is the full form of 'EVSE'? |EVSE' का पूर्ण रूप क्या है? A. Energy Variable Supply Equipment | एनर्जी वेरिएबल सप्लाई इक्विपमेंट B. Electronics Voltage Supply Equipment | इलेक्ट्रॉनिक वोल्टेज सप्लाई इक्विपमेंट C. Electric Voltage System Equipment | इलेक्ट्रिक वोल्टेज system इक्विपमेंट D. Electric Vehicle Supply Equipment | इलेक्ट्रिक व्हीकल सप्लाई इक्विपमेंट 30 / 75 Category: Electrician Second Year CBT Paper (TT)16. What is the main use of A.C drive? |A.C ड्राइव का मुख्य उपयोग क्या है? A. Interlocking system in industries | उद्योगों में इंटरलॉकिंग प्रणाली B. High starting torque | हाई स्टार्टिंग टॉर्क C. Group drive motors | समूह ड्राइव मोटर्स D. Control stepless speed in motors | मोटरों में नियंत्रण रहित गति 31 / 75 Category: Electrician Second Year CBT Paper (TT)17. Which is used to store the electrical energy in the form of electro static energy? |विधुत ऊर्जा को इलेक्ट्रो स्टैटिक ऊर्जा के रूप में संग्रहीत करने के लिए किसका उपयोग किया जाता है? A. Thermistor | थर्मिस्टर B. Capacitor | कॅपेसिटर C. Inductor | इंडक्टर D. Resistor | रेसिस्टर 32 / 75 Category: Electrician Second Year CBT Paper (TT)18. Why the A.C drives are better suited for high speed operation? |हाई स्पीड ऑपरेशन के लिए A.C ड्राइव बेहतर क्यों है? A. Having lighter gauge winding | हल्की गेज वाइंडिंग होना B. High starting torque | हाई स्टार्टिंग टॉर्क C. No brushes and commutation | कोई ब्रश और कम्यूटेशन नहीं D. Robust in construction | निर्माण में मजबूत 33 / 75 Category: Electrician Second Year CBT Paper (TT)19. Which is the application of automatic stepped voltage stabilizer? |स्वचालित स्टेप्ड वोल्टेज स्टेबलाइजर का अनुप्रयोग कौन सा है? A. Geyser | गीज़र B. Television | टेलीविज़न C. Pump motor | पम्प मोटर D. Grinder | ग्राइंडर 34 / 75 Category: Electrician Second Year CBT Paper (TT)20. What is the use of the voltage dependent resistor? |वोल्टेज पर निर्भर प्रतिरोधक का उपयोग क्या है? A. For the over voltage protection | ओवर वोल्टेज सुरक्षा के लिए B. For the impendance measurement | प्रतिबाधा माप के लिए C. For the resistance measurement | प्रतिरोध माप के लिए D. For the temperature compensation | तापमान क्षतिपूर्ति के लिए 35 / 75 Category: Electrician Second Year CBT Paper (TT)21. Which operation the control circuit is used?कण्ट्रोल सर्किट का उपयोग किस ऑपरेशन में किया जाता है? A. Forward and reverse | आगे और पीछे B. Inching | इन्चिंग C. Remote control | रिमोट कंट्रोल D. Sequential control अनुक्रमिक नियंत्रण 36 / 75 Category: Electrician Second Year CBT Paper (TT)22. What is the name of the circuit as shown in the diagram? |चित्र में दिखाए गए सर्किट का नाम क्या है? A. Power circuit of rotor resistance starter | रोटर प्रतिरोध स्टार्टर का पावर सर्किट B. Control circuit of rotor resistance starter | रोटर प्रतिरोध स्टार्टर का नियंत्रण सर्किट C. Control circuit of star delta starter | स्टार डेल्टा स्टार्टर का नियंत्रण सर्किट D. Power circuit of star delta starter | स्टार डेल्टा स्टार्टर का पावर सर्किट 37 / 75 Category: Electrician Second Year CBT Paper (TT)23. Which speed control method is applied to obtain both below normal and above normal speed in DC motor? |डीसी मोटर में सामान्य से ऊपर और नीचे दोनों गतियों को प्राप्त करने के लिए किस गति नियंत्रण विधि को लागू किया जाता है? A. Ward Leonard speed control method | वार्ड लियोनार्ड स्पीड कंट्रोल विधि B. Tapped field speed control method | टैप्ड फील्ड स्पीड कंट्रोल विधि C. Armature control method | आर्मेचर नियंत्रण विधि D. Field control method | क्षेत्र नियंत्रण विधि 38 / 75 Category: Electrician Second Year CBT Paper (TT)24. Which method is applied to control the speed of 3 phase squirrel cage induction motor using a slip ring induction motor? |स्लिप रिंग इंडक्शन मोटर का उपयोग करके 3 फेज स्क्विरल केज इंडक्शन मोटर की गति को नियंत्रित करने के लिए कौन सी विधि लागू की जाती है? A. Changing applied frequency | आरोपित आवृत्ति में परिवर्तन B. Changing the number of poles | ध्रुवों की संख्या बदलना C. Cascade operation | कैस्केड संचालन D. Changing applied voltage | आरोपित वोल्टेज बदल रहा है 39 / 75 Category: Electrician Second Year CBT Paper (TT)25. What is the name of the substation that all equipment of substation is installed within the station building? |उस सबस्टेशन का नाम क्या है जिसके सभी उपकरण स्टेशन भवन के भीतर स्थापित किए गए हैं? A. Indoor substation | इनडोर सबस्टेशन B. Pole mounted substation | पोल माउंटेड सबस्टेशन C. Plinth mounted substation | प्लिंथ माउंटेड सबस्टेशन D. Outdoor substation | आउटडोर सब स्टेशन 40 / 75 Category: Electrician Second Year CBT Paper (TT)26. Which circuit is essential to maintain oscillations or waves in an oscillator circuit? |दोलक सर्किट में दोलनों या तरंगों को बनाए रखने के लिए कौन सा सर्किट आवश्यक है? A. Negative feed back | नकारात्मक फीडबैक B. Positive feed back | सकारात्मक फीडबैक C. Voltage multiplier | वोल्टेज गुणक D. Rectifier with filter | फिल्टर के साथ दिष्टकारी 41 / 75 Category: Electrician Second Year CBT Paper (TT)27. What is the reason for widened barrier in a reverse biased diode? |रिवर्स बायस्ड डायोड में चौड़ी बाधा का कारण क्या है? A. Minority carriers in two materials are neutralised | दो सामग्रियों में अल्पसंख्यक वाहक उदासीन होना B. Electrons and holes are attracted towards supply terminals | इलेक्ट्रॉन और होल आपूर्ति टर्मिनलों की ओर आकर्षित होते हैं C. Holes in P material attracted to positive terminal | P सामग्री में होल सकारात्मक टर्मिनल की ओर आकर्षित होते हैं D. Electron in N material is drifted to negative terminal | N सामग्री में इलेक्ट्रॉन ऋणात्मक टर्मिनल की ओर प्रवाहित होता है 42 / 75 Category: Electrician Second Year CBT Paper (TT)28. What is the name of rule as shown in figure? |चित्र में दिखाए अनुसार नियम का नाम क्या है? A. Fleming's right hand rule | फ्लेमिंग का दाहिना हाथ नियम B. Thumb rule | थम्ब नियम C. Palm rule | पाम नियम D. Fleming's left hand rule | फ्लेमिंग का बाएँ हाथ का नियम 43 / 75 Category: Electrician Second Year CBT Paper (TT)29. What is the advantage of using rotating field type of an alternator? |घूर्णन क्षेत्र प्रकार के अल्टरनेटर का उपयोग करने का क्या लाभ है? A. Easy to locate the faults in the field | क्षेत्र में दोष का पता लगाना आसान है B. Easy to dissipate the heat during running | दौड़ने के दौरान गर्मी को फैलाना आसान C. Easy to connect the load with alternator | अल्टरनेटर के साथ लोड को कनेक्ट करना आसान है D. Two slip rings only required irrespective of No. of phases | दो स्लिप रिंगों की आवश्यकता होती है, चाहे फेज़ों की संख्या कितनी भी हो 44 / 75 Category: Electrician Second Year CBT Paper (TT)30. Why sequential control of motors are required in an industrial application? |औद्योगिक अनुप्रयोग में मोटरों के अनुक्रमिक नियंत्रण की आवश्यकता क्यों होती है? A. To reduce power consumption | बिजली की खपत को कम करने के लिए B. To minimise the operating cost | परिचालन लागत को कम करने के लिए C. To increase the accuracy of operation | ऑपरेशन की सटीकता बढ़ाने के लिए D. To share more loads | अधिक भार साझा करने के लिए 45 / 75 Category: Electrician Second Year CBT Paper (TT)31. What is the input ripple frequency (Fin) of full wave rectifier? |फुल वेव रेक्टिफायर का इनपुट रिपल फ्रिक्वेंसी (Fin) क्या है? A. Fᵢₙ = 2 Fᵢₙ B. Fᵢₙ = Fᵢₙ C. Fᵢₙ = √2 Fᵢₙ D. Fᵢₙ = ½ F 46 / 75 Category: Electrician Second Year CBT Paper (TT)32. What is the formula for shunt field current Rsh of a DC shunt generator if VT Terminal voltage Eg = generated EMF? |यदि VT टर्मिनल वोल्टेज Eg = उत्पन्न EMF है, तो DC शंट जनरेटर के शंट फील्ड करंट Rsh का सूत्र क्या है? A. Iₛₕ = Vₜ / Rₛₕ B. Iₛₕ = Eg x Rₛₕ C. Iₛₕ = Eg / Rₛₕ D. Iₛₕ = Vₜ x Rₛₕ 47 / 75 Category: Electrician Second Year CBT Paper (TT)33. Which method of the parallel operation of alternator is shown in the diagram? |चित्र में अल्टरनेटर के समान्तर संचालन की कौन सी विधि दर्शाई गई है? A. Dark & Bright lamp method | अँधेरा और उजियाला दीपक विधि B. Moving iron type synchroscope method | मूविंग आयरन टाइप सिंक्रोस्कोप विधि C. Western type synchroscope method | पश्चिमी प्रकार सिंक्रोस्कोप विधि D. Dark lamp method | अँधेरा दीपक विधि 48 / 75 Category: Electrician Second Year CBT Paper (TT)34. What is the name of the part of hydro power plant marked as 'X" as shown in the figure? |चित्र में दिखाए अनुसार जल विधुत संयंत्र के उस भाग का नाम क्या है जिसे 'X' से चिह्नित किया गया है? A. Control gate | कन्ट्रोल गेट B. Penstock | पेनस्टॉक C. Intake | इनटेक D. Turbine | टर्बाइन 49 / 75 Category: Electrician Second Year CBT Paper (TT)35. Which type of DC generator is used for long distance distribution lines? |लंबी दूरी की वितरण लाइनों के लिए किस प्रकार के डीसी जनरेटर का उपयोग किया जाता है? A. Differential compound generator | विभेदक यौगिक जनरेटर B. Cumulative compound generator | संचयी यौगिक जनरेटर C. Shunt generator | शंट जनरेटर D. Differential short shunt compound generator | डिफरेंशियल शॉर्ट शंट कंपाउंड जनरेटर 50 / 75 Category: Electrician Second Year CBT Paper (TT)36. What is the name of the diagram used for 3phase motor winding as shown in the figure? |जैसा कि चित्र में दिखाया गया है, 3फ़ेज़ मोटर वाइंडिंग के लिए उपयोग किए गए आरेख का नाम क्या है? A. Coil connection diagram | कुंडल कनेक्शन आरेख B. Development diagram | विकास आरेख C. Ring diagram | अँगूठी का आरेख D. End connection diagram | अंत कनेक्शन आरेख 51 / 75 Category: Electrician Second Year CBT Paper (TT)37. What is the name of the generator as shown in the circuit? |जैसा कि सर्किट में दिखाया गया है जनरेटर का नाम क्या है? A. DC series generator | डीसी श्रृंखला जनरेटर B. Short shunt compound Generator | शॉर्ट शंट कंपाउंड जेनरेटर C. DC shunt generator | डीसी शंट जनरेटर D. Long shunt compound Generator | लॉन्ग शंट कंपाउंड जेनरेटर 52 / 75 Category: Electrician Second Year CBT Paper (TT)38. Which growler test for armature is illustrated as shown in the figure? |चित्र में दिखाए अनुसार आर्मेचर के लिए कौन सा ग्रोलर परीक्षण दर्शाया गया है? A. Shorted coil test | लघुपथित कुंडल परीक्षण B. Shorted commutator test | लघुपथित कम्यूटेटर परीक्षण C. Open coil test | खुली कुंडली परीक्षण D. Grounded coil test | जमीन का तार परीक्षण 53 / 75 Category: Employability Skill CBT Paper (II)1. Plan, Prepare, Perform is related to ______ |प्लान, प्रिपेर, परफॉर्म ______ से संबंधित है A. your resume | आपका रेज़्यूमे B. your work | आपका कार्य C. attending interview | साक्षात्कार में भाग लेना D. your personality | आपका व्यक्तित्व 54 / 75 Category: Employability Skill CBT Paper (II)2. ___________ is a code of behaviour that is based on respect, values and professionalism. |__________ व्यवहार का एक कोड है जो सम्मान, मूल्यों और व्यावसायिकता पर आधारित है। A. Workplace etiquette | कार्यस्थल शिष्टाचार B. Business | व्यवसाय C. Experience | अनुभव D. Education | शिक्षा 55 / 75 Category: Employability Skill CBT Paper (II)3. Which of the following behaviours is not a characteristic of a team player? |निम्नलिखित में से कौन सा व्यवहार टीम प्लेयर की विशेषता नहीं है? A. Listening to teammates' ideas | साथियों के विचारों को सुनना चाहिए B. Willingness to help others | दूसरों की सहायता करने की इच्छा रखनी चाहिए C. Respecting different viewpoints | विभिन्न दृष्टिकोणों(व्यूपॉइंट्स) का आदर करना चाहिए D. Taking credit for others' work | दूसरों के कार्य का श्रेय लेना चाहिए 56 / 75 Category: Employability Skill CBT Paper (II)4. Important skills required for the future of work is _______ |भविष्य के कार्य के लिए आवश्यक महत्वपूर्ण कौशल _______ हैं A. Avoid building professional relationships. | व्यावसायिक संबंध बनाने से बचना B. Avoid learning new skills. | नये कौशल सीखने से बचना C. Learn making reels and TikTok videos | रील्स और टिकटॉक वीडियो बनाना सीखना D. Master internet skills. | इंटरनेट कौशल में निपुणता प्राप्त करना 57 / 75 Category: Employability Skill CBT Paper (II)5. While making a business plan, which is not required to mention? |बिजनेस प्लान बनाते समय जिनका जिक्र करना जरूरी नहीं है? A. Personal interests and hobbies | पर्सनल इंटरेस्ट और हॉबी B. Business idea | बिजनेस आइडिया C. Startup costs | स्टार्टअप कॉस्ट D. Future growth strategies | फ्यूचर ग्रोथ स्ट्रेटेजी 58 / 75 Category: Employability Skill CBT Paper (II)6. You have an Instagram page for jewellery business. What should you do to connect with viewers? |आपके पास आभूषण व्यवसाय के लिए एक इंस्टाग्राम पेज है। आपको दर्शकों से जुड़ने के लिए क्या करना चाहिए? A. Share daily updates about your business as Stories on social media | सोशल मीडिया पर स्टोरीज़ के रूप में अपने व्यवसाय के बारे में दैनिक अपडेट शेयर करके B. Post about a T.V. show you like | आपको पसंद आने वाले टीवी शो के बारे में पोस्ट करके C. Post dance reels | डांस रील्स पोस्ट करके D. Post cooking videos | खाना पकाने के वीडियो पोस्ट करके 59 / 75 Category: Employability Skill CBT Paper (II)7. Important factors of a good resume need to be checked are _____________|एक अच्छे बायोडाटा के लिए जिन महत्वपूर्ण कारकों की जांच की जानी चाहिए वे हैं _____________ A. paper quality | कागज की गुणवत्ता B. attractive words | आकर्षक शब्द C. company details | कंपनी का विवरण D. free from spelling, grammar mistakes, correct information | वर्तनी, व्याकरण संबंधी गलतियों से मुक्त, सही जानकारी 60 / 75 Category: Employability Skill CBT Paper (II)8. The ability of a computer or machine to mimic the capabilities of the human mind is called ________|कंप्यूटर या मशीन की मानव मस्तिष्क की क्षमताओं की नकल करने की क्षमता को ________ कहा जाता है A. natural intelligence | नेचुरल इंटेलिजेंस B. artificial performer | आर्टिफिशियल परफ़ॉर्मर C. artificial intelligence | आर्टिफिशियल इंटेलिजेंस D. intellect | इन्टलेक्ट 61 / 75 Category: Employability Skill CBT Paper (II)9. Which is an example of being open to learning in the workplace? |कार्यस्थल में ओपन लर्निंग का एक उदाहरण कौन सा है? A. Refusing to attend training sessions to improve technology skills | टेक्नोलॉजी स्किल्स में सुधार के लिए प्रशिक्षण सत्रों में भाग लेने से इनकार करना B. Avoiding feedback from colleagues | सहकर्मियों से फीडबैक लेने से बचना C. Accepting and adapting to changes in work processes | कार्य प्रक्रियाओं में परिवर्तनों को स्वीकार करना और अपनाना D. Ignoring advancements in technology | प्रौद्योगिकी में प्रगति को नजरअंदाज करना 62 / 75 Category: Employability Skill CBT Paper (II)10. Taking decisions on your own, after carefully thinking about them is the quality of _______ |ध्यानपूर्वक विचार करने के बाद स्वयं निर्णय लेना _______ का गुण है A. Self-awareness | आत्म जागरूकता B. Self-belief | आत्म विश्वास C. Independent decision making | स्वतंत्र निर्णय लेना D. Grit | ग्रिट 63 / 75 Category: Employability Skill CBT Paper (II)11. When a machine operator suddenly face a problem, and quickly finds another way to do the work is called as ______ |जब एक मशीन ऑपरेटर को अचानक किसी समस्या का सामना करना पड़ता है, और वह तुरंत काम करने का दूसरा तरीका ढूंढ लेता है, तो उसे क्या कहते हैं? A. Sincerity | सिन्सेरिटी B. Integrity | इंटीग्रिटी C. Honesty | आनेस्टी D. Adaptability | अडाप्टेबिलिटी 64 / 75 Category: Employability Skill CBT Paper (II)12. Which term describes using things in a way that can last for a long time without causing harm? |कौन सा टर्म चीजों को इस तरह से उपयोग करने का वर्णन करता है जो बिना किसी नुकसान के लंबे समय तक चल सकता है? A. Eco-friendliness | एको-फ्रेंडलीनेस B. Pollution | पोलुशन C. Resources | रिसोर्सेज D. Sustainability | सस्टेनेबिलिटी 65 / 75 Category: Employability Skill CBT Paper (II)13. How can you become as self-employed? |आप स्व-रोज़गार कैसे बन सकते हैं? A. Work in a company | किसी कंपनी में काम करके B. Thinking about to become as self-employed | स्व-रोज़गार बनने के बारे में सोच कर C. Joining MBA course | MBA कोर्स में शामिल होकर D. Try your idea on a small scale, join relevant short term course | अपने विचार को छोटे पैमाने पर ट्राइ करके, शार्ट टर्म कोर्स में शामिल होकर 66 / 75 Category: Employability Skill CBT Paper (II)14. While doing some difficult work, if it is not going on well, what we have to do? |कोई कठिन काम करते समय यदि वह ठीक से नहीं चल रहा हो तो हमें क्या करना होगा? A. Ask someone else to do it for you | किसी और को आपके लिए यह करने के लिए कहना चाहिए B. Keep trying and look for another way | प्रयास करते रहें और दूसरा रास्ता खोजना चाहिए C. Take a break and give up | थोड़ा ब्रेक लें और हार मान लेना चाहिए D. Get upset and quit trying | परेशान हो जाएं और प्रयास करना छोड़ देना चाहिए 67 / 75 Category: Employability Skill CBT Paper (II)15. Campus recruitment is conducted at ______ |कैम्पस भर्ती ______ में आयोजित की जाती है । A. in a company | कंपनी में B. ITI | आईटीआई C. on line | ऑनलाइन D. capital city of the state | राज्य की राजधानी में 68 / 75 Category: Employability Skill CBT Paper (II)16. What is the standard way in which computers connected wireless? |कंप्यूटरों को वायरलेस तरीके से कनेक्ट करने का मानक तरीका क्या है? A. LAN | लेन B. Wi-Fi | वाई-फाई C. WAN | वैन D. ISP | आई0एस0पी 69 / 75 Category: Employability Skill CBT Paper (II)17. If someone wants to sell home made products, what they have to do, to grow the business? |अगर कोई घर में बने उत्पाद बेचना चाहता है तो उसे व्यवसाय बढ़ाने के लिए क्या करना होगा? A. Find shopkeepers and build marketing with them | दुकानदारों को ढूंढ कर और उनके साथ मार्केटिंग बनाना चाहिए B. Keep doing the same thing without any changes | बिना किसी बदलाव के वही काम करते रहना चाहिए C. Wait for an opportunity to grow the business | व्यवसाय बढ़ाने के अवसर की प्रतीक्षा करनी चाहिए D. Only sell to her neighbours | केवल उसके पड़ोसियों को ही बेचना चाहिए 70 / 75 Category: Employability Skill CBT Paper (II)18. A person with high emotional intelligence has _______ |उच्च भावनात्मक बुद्धिमत्ता वाले व्यक्ति के पास ______ होता है । A. lot of negative qualities | बहुत सारे नकारात्मक गुण B. physical strength | फिजिकल स्ट्रेंथ C. ego | ईगो D. lot of positive qualities | बहुत सारे सकारात्मक गुण 71 / 75 Category: Employability Skill CBT Paper (II)19. Which of the following best describes the self-management skill of reliability? |निम्नलिखित में से कौन विश्वसनीयता के सेल्फ मैनेजमेंट स्किल का सबसे अच्छा वर्णन करता है? A. Not being honest with colleagues | सहकर्मियों के साथ ईमानदार न रहना B. Not completing tasks on time | समय पर कार्य पूरा नहीं करना C. People always trust you to do your job well | लोग हमेशा आप पर भरोसा करते हैं कि आप अपना काम अच्छी तरह से करेंगे D. Ignoring the needs of others | दूसरों की ज़रूरतों को नज़रअंदाज़ करना 72 / 75 Category: Employability Skill CBT Paper (II)20. The word 'resume' comes from French and means ________ |रेज़्यूमे' शब्द फ़्रेंच भाषा से आया है और इसका अर्थ ________ है । A. summary | संक्षेप B. Experience | अनुभव C. education | शिक्षा D. placement | प्लेसमेंट 73 / 75 Category: Employability Skill CBT Paper (II)21. The ability to wait and stay calm ______ |प्रतीक्षा करने और शांत रहने की क्षमता ______ है । A. creativity | क्रिएटिविटी B. patience | पेशेंस C. problem solving | प्रॉब्लम सॉल्विंग D. interpersonal skill | इंटरपर्सनल स्किल 74 / 75 Category: Employability Skill CBT Paper (II)22. While applying for a job through email, what are the documents need to be attached? |ईमेल के माध्यम से नौकरी के लिए आवेदन करते समय, कौन से डाक्यूमेंट्स संलग्न करने की आवश्यकता है? A. Photographs from childhood | बचपन की फोटो B. Address Proof | निवास प्रमाण पत्र C. Resume, Course and Training Certificates | बायोडाटा, कोर्स और प्रशिक्षण प्रमाणपत्र D. Birth certificate | जन्म प्रमाणपत्र 75 / 75 Category: ES 2 Year Module 2- Future Work Skills1. Which of the following best describes the gig economy? A. A system where workers are paid a fixed monthly salary B. A system where workers take on part-time or temporary jobs C. A system where employees work full-time for a single employer D. A system where workers have fixed work hours and locations Your score isThe average score is 17% 0% Restart quiz Exit WhatsApp और YouTube चैनल से जुड़े रहनाWhats App Electrician Free CBT Practice SetCOPA Free Practice SetDraughtsman Civil Free CBT Practice SetDraughtsman Mechanic Free CBT Practice SetITI CBT Practice Set Second YearElectronic Mechanic Free CBT Practice Set अत्यधिक चर्चा में आईटीआई में एडमिशन के लिए शारीरिक और मानसिक रूप से फिट होना क्यों जरूरी है? – जानिए दिव्यांग आरक्षण के नियम🎯 Uttar Pradesh – ITI Admission form 2025 Start – Apply Online PRN Generate करने के लिए आधार कार्ड क्यों जरूरी है? ITI छात्रों के लिए वेरिफिकेशन का अंतिम मौका: न चूकें! सत्र 2024 West Bengal ITI Admission form 2025 Start – Apply Online नॉर्दर्न कोलफील्ड लिमिटेड (एन०सी०एल) तकनीशियन भर्ती 2025 – आवेदन करें 200 पोस्ट के लिए।